Duplex Stainless Steel 2205 Coil: supplier, stockist and exporter in Mumbai, India
Rajgranth Metal & Alloys supplies duplex stainless steel 2205 coil (UNS S32205) from Mumbai and exports it to 18 markets.
What is Duplex 2205 coil?
Coil is flat-rolled material supplied wound on a core, for processors who slit, blank or roll-form it. Duplex 2205 coil is bought by tube mills, press shops and fabricators that need continuous feedstock. Duplex 2205 (UNS S32205 and S31803, EN 1.4462) has a mixed austenitic and ferritic structure with 22 percent chromium, about 5 percent nickel and 3 percent molybdenum, plus nitrogen. It is about twice as strong as 316L and resists chloride pitting and stress corrosion cracking better.
Rajgranth Metal & Alloys lists Duplex 2205 among the grades it supplies and exports from Mumbai.
Duplex 2205 designations and equivalents
| Standard | Designation |
|---|---|
| UNS | S32205 |
| EN / Werkstoff | 1.4462 |
| Also called | S31803, 2205, UNS S31803 |
Scroll the table horizontally to see all columns.
Duplex 2205 chemical composition
Limits are those of the standard named in the table caption. Product-specific standards for pipe, tube and bar carry their own limits, so always confirm the composition on the mill test certificate supplied with the material.
| Element | Carbon | Manganese | Silicon | Phosphorus | Sulphur | Chromium | Nickel | Molybdenum | Nitrogen |
|---|---|---|---|---|---|---|---|---|---|
| Limit | 0.030 max | 2.00 max | 1.00 max | 0.030 max | 0.020 max | 22.00 – 23.00 | 4.50 – 6.50 | 3.00 – 3.50 | 0.14 – 0.20 |
Scroll the table horizontally to see all columns.
Duplex 2205 mechanical properties
| Property | Requirement |
|---|---|
| Tensile strength | 655 MPa minimum |
| Yield strength (0.2% offset) | 450 MPa minimum |
| Elongation in 50 mm | 25% minimum |
| Hardness | 31 HRC maximum (293 HBW) |
Scroll the table horizontally to see all columns.
Duplex 2205 coil: sizes and finishes
The published size range, finishes and conditions for coil are set out on the coils pages, which list every dimension we publish. Sizes outside the range can be produced to order; send the dimensions with your enquiry.
| Parameter | Range |
|---|---|
| Thickness | 0.3 mm, 8 mm |
| Width | 100 mm, 2000 mm |
| Coil ID | 508 mm, 610 mm |
Scroll the table horizontally to see all columns.
Standards for Duplex 2205 coil
Duplex 2205 coil is commonly specified to ASTM A240 / ASME SA-240 and ASTM A480. Commonly specified product standards. Confirm the standard, edition and any supplementary requirements on your order; we supply to the standard you name.
Why buyers choose Duplex 2205 coil
Roughly twice the yield strength of 316L, allowing thinner walls
Good resistance to chloride pitting and stress corrosion cracking
Lower nickel content makes its price steadier than austenitic grades
Where Duplex 2205 coil is used
- Oil and gas process and flowlines
- Desalination and seawater systems
- Chemical process vessels and pipe
- Pressure vessels and storage tanks
- Pulp and paper digesters
What to state when you enquire for Duplex 2205 coil
- Thickness in mm, 0.3 mm to 8 mm published, and width, 100 mm to 2000 mm published
- Coil inner diameter: 508 mm or 610 mm
- Coil weight, or the maximum your uncoiler takes
- Surface finish and whether film is required
- Edge: mill edge or slit edge
- The standard and the test certificate required
What to check on Duplex 2205 coil before and after delivery
On Duplex 2205 coil, check edge condition, camber and coil set on the first delivery, since these decide how the material runs on your line. Confirm the inner diameter and coil weight against your uncoiler before ordering, and the certificate chemistry, because a whole production run inherits it. Grade limits to design around: not for service above about 300 degrees C, where it loses toughness and welding needs controlled heat input to hold the phase balance.
Export of Duplex 2205 coil from India
Duplex 2205 coil is exported from Mumbai to 18 confirmed markets, quoted with the Incoterm and named port.
Duplex 2205 compared with similar grades
Buyers who look at Duplex 2205 coil usually also compare Super Duplex 2507, SS 316L and Duplex 2304. The grade pages below give each one's designations, properties and limits side by side so you can choose for the service rather than the price alone.
FAQ
09Questions answered
- What is the difference between S31803 and S32205?
- S32205 is a tighter version of the same 2205 composition, with higher chromium and nitrogen minimums. Most material is now dual-certified to both.
- Why is duplex 2205 stronger than 316L?
- The mixed ferrite and austenite structure and the nitrogen content give it a minimum yield strength of 450 MPa against 170 MPa for 316L.
- What is the temperature limit of 2205?
- It is generally used up to about 300 degrees C. Above that, it can embrittle, so check the duty before specifying it.
- What coil sizes of Duplex 2205 do you supply?
- The published range is thickness from 0.3 mm to 8 mm and width from 100 mm to 2000 mm, on a coil inner diameter of 508 mm or 610 mm. Send the requirement and we confirm.
- Which standard applies to Duplex 2205 coil?
- Duplex 2205 coil is commonly specified to ASTM A240 / ASME SA-240 and ASTM A480. Confirm the standard and edition on your order.
- What is the minimum yield and tensile strength of Duplex 2205?
- In the annealed condition, Duplex 2205 has a minimum yield strength of 450 MPa and a minimum tensile strength of 655 MPa, per the standard named in the table above.
- What is the UNS number and EN designation of Duplex 2205?
- Duplex Stainless Steel 2205 is designated UNS S32205 and EN 1.4462, and is also called S31803, 2205 and UNS S31803.
- What are the main alloying elements in Duplex 2205?
- To the standard in the composition table, Duplex 2205 carries chromium 22.00 – 23.00, nickel 4.50 – 6.50 and molybdenum 3.00 – 3.50 percent by weight. Confirm the composition on the mill test certificate supplied with your material.
- Do you supply a mill test certificate with Duplex 2205 coil?
- Yes, to EN 10204 3.1 as standard, showing chemistry and mechanical properties against the heat. EN 10204 3.2 with third-party inspection is available on request.
Products
Compare
Export
Industries
Guides
Send us the specification.
Grade, dimensions, quantity and standard. We will come back with availability and price.